Views: 0 Author: Site Editor Publish Time: 2026-11-20 Origin: Site
A dredge stops for small parts more often than for big failures. A worn tooth, a blown hose or a winch brake that will not hold can idle a vessel for a day. If you run several machines, the problem is not finding a part once; it is knowing which parts to hold in stock for each hull.
We are ITECH Co.,Ltd., and we build spare-parts lists around a dredge fleet, machine by machine. Below we cover cutter heads and teeth, winches and anchors, hose and pipeline, and the generators and pumps that keep a unit working. The aim is a stock list you can defend to finance and still use on a wet deck.
A dredger is a set of wear interfaces. The cutting end is the cutter head and its teeth. The holding system is winches, anchors and mooring gear. The transport path is rubber hose, floating line and steel or HDPE pipe. Power comes from generators and pumps. Each interface wears at its own rate, so each needs its own stock rule.
Cutting, holding and conveying happen at once. Cutter heads loosen the bed, winches pull the ladder forward, and the pump moves slurry through the line. When one part fails the whole chain stops. Browse our dredging equipment range to see how we group replacement items.
We list parts by hull, not by catalogue chapter. Two dredgers of different sizes may share a tooth type but not a hose diameter. A single list that ignores that difference puts the wrong stock in the wrong port. We also mark which port each item ships from, because a part held in the wrong country is not stock in the eyes of a vessel waiting on a quay.
Wear items are consumed on schedule. Cutter teeth and hose liners do not fail at random; they wear down with hours in abrasive material. Holding them before they are needed turns a day of delay into a short change-out.
A part that fits the drawing but not the interface still costs you a day. We check flange patterns, pin sizes and hose ends against the machine before we confirm an order.
Most lost hours come from cheap components: a seal, a brake pad, a coupling. Stocking those alongside the expensive items keeps a small fault from becoming a long lay-up.
The figures below come from our published range. Anything else stays open until we confirm it in writing.
We list cutter heads from 8 inch up to 36-38 inch, including 10-12, 14-16, 16-18, 20-22, 24-26, 26-28, 28-30, 32-34 and 34-36 inch steps. Cutter teeth are supplied as replacement sets. The tooth grade and pin pattern for a given head are to be confirmed in writing.
Our range includes hauling, multi-purpose, hydraulic and marine electric mooring winches. Match by pull load, drum size and control type. Exact ratings per unit are to be confirmed in writing.
Rubber discharge hoses cover DN200 to DN1300. We also supply HDPE, PE, UHMWPE and steel dredge pipes, plus floaters for the floating line. Wall thickness and pressure rating for a specific hose are to be confirmed in writing.
Dredging equipments also include the pumps and generators that drive the work. Floaters keep the discharge line at the right height as the vessel moves. Generator output and pump rating for a package are to be confirmed in writing.
Not every interface is standard. Send the head drawing or hose end detail and we will match it. Any value not published here stays to be confirmed in writing.
Cutter head sizes published in our range | |||
Head size | Published size step | Confirm in writing | Typical role |
|---|---|---|---|
Small | 8 inch | Tooth grade and pin pattern | Pond and narrow ditch |
Mid-small | 10-12 inch | Tooth grade and pin pattern | Canal maintenance |
Mid | 14-16 inch | Tooth grade and pin pattern | River bank work |
Mid-large | 20-22 inch | Tooth grade and pin pattern | Port maintenance |
Large | 28-30 inch | Tooth grade and pin pattern | Capital dredging |
Extra large | 36-38 inch | Tooth grade and pin pattern | Heavy clay and rock |
A matched head and tooth set cuts more consistently than a mixed set. We supply the head sizes listed above and the teeth that go with them, so you can change a worn crown without re-cutting the ladder. Full dredging equipment components are listed by assembly.
Hauling and mooring winches are chosen for the pull the ladder needs, not for the largest model on the page. Hydraulic units suit a dredger with a spare circuit; marine electric units suit a simpler deck.
The dredge rubber hose takes the movement between the floating line and the shore line. Steel and HDPE pipe handle the long run, and floaters hold the line up. Mixing diameters without a plan creates a choke point.
CSDs consume teeth, liner plates and hose faster than any other item. A fleet list should start with those three and add winch and pump spares behind them. On a rock job, double the tooth allowance before the first month rather than after the first stoppage.
Smaller units use fewer parts but still need hose, pump seals and generator filters. Their advantage is that one stock kit can serve several machines.
Maintenance work changes material often, so wear rates swing. Keep a wider range of tooth grades and hose sizes than you would for a single borrow pit.
Coarse material shortens hose and tooth life. Here the stock question is not whether to carry spares but how many sets to hold before the next delivery.
Fleet-matched spare parts versus generic replacements | ||
Dimension | Fleet-matched spare part | Generic replacement part |
|---|---|---|
Selection basis | Chosen from your hull and interface | Chosen from a catalogue size |
Material data | Grade stated in writing | Grade may be unspecified |
Fit check | Pin, flange and hose end checked | Fit confirmed at the fitting stage |
Stock planning | Listed machine by machine | One list for all vessels |
Failure pattern | Wear tracked per part and site | Wear tracked by invoice only |
Best use | Planned maintenance across a fleet | One-off repair on a single unit |
Write one line per machine: size, pipe diameter, winch type and power unit. That line is the filter for every part decision. A catalogue that ignores it will send you the right part for the wrong hull.
Rank items by consumption, not by unit price. Teeth and hose may be cheap each but expensive in downtime. A single gearbox on the shelf will not help if you run out of couplings. A simple rule we use is to rank the last twelve months of stoppages by cause and start the list at the top of that column.
Before you order, confirm pin sizes, flange drilling and hose end type. Take a photo of the worn part as well as the drawing; the drawing is often older than the machine.
Holding every part ties up cash. Holding none ties up vessels. We set the split by how quickly a part can reach the site and what a day of delay costs you. Write the delay cost beside each line; a part that saves two days is worth more than its price suggests.
Two hoses with the same diameter can have very different wall construction. Ask for material and pressure rating in writing and put it on the purchase order.
Spare hose and heads are heavy. Store them on racks that a fork lift can reach, and keep the storage close to the quay so loading does not become a project.
When you fit a new hose or head, check the couplings and pins it sits on. A new part on a worn interface fails quickly; replace both together.
Match the stock list to the contract. A port job needs different hose lengths from a river job, and a winter stop needs more filters and seals than a summer one.
Request one sheet with size, material, interface and quantity. Mark any unpublished figure to be confirmed in writing. Compare offers on that sheet, not on the sales email.
If your dredger has been modified, send the drawing. Most components can be adapted, but the change must be agreed before the batch is made.
For wear parts, a sample of the old item is worth more than a part number. It shows the wear pattern and confirms the interface. Keep one cleaned sample per machine, labelled with the hull and the date it came off, so the next change-out can be compared against it.
Our online service team replies within eight hours. Tell us the machine and the part you need; we will confirm the match and flag any figure that needs writing.
We have built dredging equipment since 1994, with more than thirty years in the field. Our ISO 9001 certified facilities use robotic welding, and we keep an in-house group working on wear parts. We have shipped to many countries; the exact count is to be confirmed in writing.
In spares, our value is the list as much as the parts. We start from your hulls, mark what is published and what is to be confirmed in writing, and hand you a sheet your storekeeper can use. It is less exciting than a new dredger and far more useful on a Monday morning.
Start with the items that wear on a clock: cutter teeth, hose sections, impeller liners and pump seals. Add winch brake parts and generator filters behind them. The exact mix follows each hull, so list parts by machine rather than by a single fleet average.
Our published range runs from 8 inch to 36-38 inch, including 10-12, 14-16, 16-18, 20-22, 24-26, 26-28, 28-30, 32-34 and 34-36 inch steps. Replacement cutter teeth are also listed. Confirm tooth grade and pin pattern in writing for your head.
Start with the nominal diameter: our rubber hoses cover DN200 to DN1300. Then confirm pressure rating, wall construction and end fitting against the line, since two hoses of the same diameter can behave differently. Send the old hose detail and we confirm in writing.
Some are fine, but the risk sits in the interface and the material grade. A part that fits the drawing may still wear out early if the alloy differs. We compare on size, material and fixing detail, and we state in writing what we can confirm.
Yes. Send the machine list with pipe diameter, winch type and power unit for each hull. We return a stock sheet that marks published items and flags figures to be confirmed in writing, so your store and your finance team read the same document.