-
Capacity separates the models more than horsepower does. This guide reads the published CSD series from 500 m3/hr at 200 mm up to 7000 m3/hr at 750/700 mm, then sets depth and discharge distance against that figure. It places the small units, the mid band and the largest frames against real job types, and shows where a long pipeline eats the capacity you planned. Useful when a tender sits between two sizes and someone has to justify the choice on paper and on site.
-
Spare lists work best when they are written per hull, not per catalogue. Our order of priority puts cutter teeth and hose first, then winch, pump and generator items. The published cutter head range runs from 8 to 36-38 inch, with rubber hose from DN200 to DN1300 and several winch types. A procurement view weighs stock cost against vessel stop time and keeps every unpublished rating for written confirmation, giving the storekeeper and the finance team the same sheet on every order.
-
Hydraulic power is sized before the impeller on deep suction work. Our sizing starts with oil flow and pressure, which follow discharge distance, static lift and solids load. Low-speed torque earns its keep in compacted ground, where an electric drive may stall. The piece reviews the published HSPD 80 to 300 classes, the gap between geometric depth and real hydraulic reach, jet assistance under clay, and the filter and seal routine that keeps a pack working. Written for tender teams weighing drive types.
-
Pump selection starts with a solids sample, not a power rating. This piece sets out how flow, head and concentration define the duty point, then compares submersible and mounted layouts, high-chrome versus stainless wet parts, and open against closed impellers. It covers the ESPD and HSPD size range, the 250 mm portable build, and the figures that stay unconfirmed until a written data sheet is issued. Written for engineers and buyers who need a defensible shortlist before they send an enquiry.
-
A pond rarely has one problem, which is why a single fixed tool wastes so much time on small sites. This page works through the five published heads — bucket, pump, weed cutter, collecting rake and T-type cutter — and shows how the carrier, hull and access route narrow the choice. It compares crawler-based amphibious units with floating dredgers, explains where aluminium helps, and lists the AMD200, AMD220, AMD450 and AMV2100 models. Managers of ponds, canals and shallow basins will find a head-selection matrix and a clear pass-order plan.
-
An 18-inch line is a system, not a size label. This page treats the DRAGA MARINA 18" SUCCION/DESCARGA as a pump-and-pipe matching exercise for Latin American buyers, and explains why suction layout, discharge route and solids size have to be settled together. It uses the published CSD series as context while marking unspecified 18-inch figures for written confirmation. Readers planning river desilting, port maintenance, reclamation fill or lagoon cleanup will find a configuration matrix, a wear-and-spares approach and clear guidance on what a custom build can change.
-
A dredge that cannot clear the bridge never reaches the water, so logistics sets the limit before the pump does. This deployment note covers road haul against barge, electric against hydraulic power on board, and the bank conditions that decide how fast a portable unit starts. It also marks where a trailer rig gives way to a cutter suction dredger and lists the figures confirmed in writing before any machine leaves the yard for a scattered, short-cycle job with a small crew.
-
Hard rock does not defeat a cutter suction dredger; it defeats the wrong cutting tool. This page reads "diamond dredging equipment" as a duty, not a product name, and sets out how teeth, heads and pump wet ends share the wear load. It gives the published CSD working envelope, the cutter head size bands and a checklist for abrasive-ground configuration. Buyers planning river channels, clay overburden, port maintenance or reclamation fill will find the trade-offs between head size, pipe bore and spares stock, plus a direct comparison with mechanical digging.
-
A dredge that cannot clear the bridge never reaches the water, so logistics sets the limit before the pump does. This deployment note covers road haul against barge, electric against hydraulic power on board, and the bank conditions that decide how fast a portable unit starts. It also marks where a trailer rig gives way to a cutter suction dredger and lists the figures confirmed in writing before any machine leaves the yard for a scattered, short-cycle job with a small crew.
-
One row on the JSD250 data sheet decides most orders: the 200-to-1000 m discharge range, because it trades against the 15 m digging depth. This spec walkthrough reads each figure with its site condition attached, from the 130-260 m3/hr capacity and 10/8 inch pump to the 60-70 mm gravel limit and 180-250 kW engine. Buyers see where a jet system lifts sand from under clay, how to size power without guesswork, and which figures stay open to written confirmation before a deposit is placed.
-
Compacted beds punish pumps that were sized for free-flowing sand. This selection note walks through the two inputs we ask for first—slurry density and cutterhead layout—and shows where a twin-cutter electric unit earns its price over a single-cutter or hydraulic setup. It covers high-chrome wet parts, the density ceilings we will not quote without site data, and the port, dewatering, and tailings jobs where a submersible frame beats a surface-mounted pump. Buyers get a configuration checklist and a clear list of what stays to be confirmed in writing.
-
Channel dredging equipment for navigation depth: survey and trigger levels, dredger selection for soft and hard beds, disposal, environmental windows and how to budget a maintenance channel programme.