Views: 0 Author: Site Editor Publish Time: 2026-11-19 Origin: Site
When a dredging job moves from sand into weathered rock or dense gravel, the cutting tool becomes the cost centre. Tooth wear climbs, the head loses bite, and every hour spent changing parts is an hour the pump is not moving slurry. Buyers searching for diamond dredging equipment want tooling that survives abrasive ground without stopping the spread. We treat the phrase as a search term for hard-rock dredging, not a product name. ITECH Co.,Ltd. builds cutter suction dredgers and the teeth and heads that match them.
We start every enquiry with the material, not the machine. Give us a grain-size band, a weathering profile and the hours you need between tooth changes, and we will match the tooling to it. This page covers abrasive wear, how teeth and heads work as a system, and where a cutter suction dredger beats mechanical digging.
The working end of an abrasive-duty dredge is a dredge cutter head on the ladder, with replaceable teeth around its crown. Behind it sit the suction mouth, slurry pump, discharge pipeline and the winches that swing the ladder. We publish heads from 8 inch through the 36–38 inch band, plus matching teeth as spares. There is no "diamond" model in our range; the word describes the duty.
The head rotates against the bottom and cuts or rips material loose. Grains mix with water at the suction mouth and travel as slurry to the placement area. Tooth geometry and head speed decide how much energy goes into fracture rather than pushing material aside. In clay or rock, we size the cutting force first, then check the pump can carry what the head releases. Reversing that order is the common cause of a machine that digs well but performs poorly.
Abrasion removes metal at the tip long before the rest of the head is tired. We read quartz content, grain angularity and impact cycles per hour, then recommend a tooth profile that keeps an edge. Harder metal alone rarely helps if the shape is wrong. Alloy grades and hardness are to be confirmed in writing.
A head too heavy for the ladder wastes power and slows the swing. One too light chatters and sheds teeth. We match head diameter and mass to the dredger class and the depth you work in, not to the largest the ladder can carry. That balance decides cubic metres placed per fuel litre.
Cutting is half the job. A cutter suction dredger removes loosened material in the same pass, so the tool never re-cuts the same ground. Re-handling rock fragments doubles wear for no extra placed volume. Steady flow also keeps the suction mouth clear.
We build a spares list around cutting hours rather than a guess. Teeth, pins, heads, hoses and pump wet ends wear at different rates. Knowing which item sets your maintenance interval lets you stock the right quantity and avoid idle days waiting for one part.
Tooth and head material follows the mineral hardness of the ground. We publish heads and teeth as replacement parts; specific alloy chemistry, hardness and service hours are to be confirmed in writing. We specify pump wet ends alongside the cutting tool so the slurry path stays consistent.
Published head bands run 8 inch, 10–12, 14–16, 16–18, 20–22, 24–26, 26–28, 28–30, 32–34, 34–36 and 36–38 inch. Head size must suit the ladder and pipe bore. We do not pair a large head with a small pump; the solids released have to be transportable.
Our CSD series sets the envelope. The CSD-200 is rated 500 m³/hr at 1–5 m with 200/200 mm pipes and 160–300 kW. The CSD-300 reaches 1,200 m³/hr at 1–12 m with 300/300 mm pipes and 400–600 kW. CSD-500 and CSD-700 reach 3,500 and 7,000 m³/hr. Rock duty lowers these figures; we quote achievable output after reviewing your material.
Power runs from 160–300 kW on the smallest class to 2,800–3,500 kW on the largest. Hoses are published from DN200 to DN1300, with pipe in HDPE, PE, UHMWPE or steel. Abrasive slurry favours thicker pipe. Final pump and pipe matching is to be confirmed in writing.
Standard dredgers are dismountable and road-transportable, and custom builds are accepted. We align the spares package with your planned cutting hours. Quantities, delivery and packing are to be confirmed in writing, since they depend on the class and the abrasion profile you provide.
For clay, hardpan and weathered rock, we start with a head whose teeth break material rather than polish it. Bands from 10–12 up to 36–38 inch cover most ladders. Choice rests on depth and pipe bore, not the name of the rock.
A kit keeps downtime short. We group dredge cutter teeth, pins, heads, hoses and pump wet ends into one order so spares arrive together. Contents are built around your duty and confirmed in writing before production.
When the standard series does not fit, we build to the project: a different ladder depth, pipe diameter or wear package. Send the material profile and placement distance, and we will propose a configuration with the trade-offs stated.
Gravel-laden rivers wear teeth fast, especially where the bed is armoured. We set the head to bite below the armour and size the pump for the solids that follow. The aim is steady advance, not bursts of output followed by long changes.
Cutter suction dredgers are stated to handle compacted soil, clay and rock. Layered ground asks one tool to cross soft overburden and a hard band without a rebuild. We plan tooth patterns that tolerate both and flag where output drops.
Maintenance rewards predictable wear over peak speed. A head that keeps its profile through a season cuts shutdowns in a busy fairway. We work around traffic windows when planning the cutting schedule.
Where dredged material becomes fill, grain size and contamination matter as much as output. A head that makes consistent fragments helps downstream screening. We match the tool to the fill specification you must meet.
Both routes can move hard material, but they suit different site and placement conditions. This comparison is between generic processes, not equipment brands.
CSD cutting vs mechanical digging on abrasive ground | ||
Decision factor | Cutter suction dredging | Mechanical excavation |
|---|---|---|
Material state | Cut and pump as slurry in one pass | Dig, load and haul in stages |
Placement distance | Economical over long pipeline runs | Costs rise quickly with haul distance |
Water depth | Works from a floating spread, depth per series table | Limited by reach and ground bearing |
Wear exposure | Concentrated in teeth, head and pump wet ends | Spread across buckets, tracks and trucks |
Output pattern | Continuous flow, steady solids rate | Batch cycles with variable waits |
Key limit | Solids size must pass the pump and pipe | Cannot place material far underwater cheaply |
Start with the ground. Quartz content, angular grains and weathering depth tell us how fast a tooth loses its edge. A sample and a short note are enough for a first pass. Without them, any wear estimate is a guess.
Tell us how long you want a tooth set to last. That figure drives the profile and the size of the spares basket. Chasing the longest interval can raise unit cost; we show where the balance sits for your site.
A head that releases more solids than the pipe can carry creates blockages and wear. We check diameter, bore and pump capacity together. Published pipe options run DN200 to DN1300, so there is room to choose.
Compare quotations on consumed parts, not just the machine price. A cheaper head that sheds teeth twice as fast can cost more in one season. Ask for tooth, pin, hose and wet-end pricing together.
Dismountable units suit sites without a slipway. Check the depth band against the series table before you commit. Work beyond the published envelope needs a written proposal.
Abrasive-ground configuration checklist | ||
Checkpoint | What we ask you | Why it changes the build |
|---|---|---|
Mineral hardness | Quartz and feldspar content | Sets tooth profile and alloy choice |
Grain shape | Angular or rounded grains | Angular grains accelerate tip wear |
Weathering depth | Metres of soft overburden | Decides whether one head covers the layer |
Swing cycle | Hours per day of cutting | Drives spares quantity on site |
Discharge route | Pipeline length and lift | Fixes pump duty and pipe class |
Placement spec | Fill or disposal requirement | Limits fragment size and slurry density |
The ladder carries the head and the cutting load, so its structure must match the head mass. A floating spread also needs stability for the swing forces rock generates. We review ladder and pontoon before confirming a heavier package.
Teeth sit in retainers on the head crown so they can be changed on deck. The method must survive repeated impact without loosening. We specify the retention and the tools needed for a change-out in writing.
Check access, depth, placement distance and the hours you can stop for maintenance. An abrasive site with narrow shut-down windows needs more spares on site. We build those constraints into the configuration.
Compare depth, output, pipe bore and power on the same basis. Our series table gives each class; exact tooth life and alloy grade are to be confirmed in writing before you rely on them.
Tell us which constraint is fixed and which can move. If depth is fixed, we may change bore or wear package. Custom builds are accepted, but one change usually shifts cost or output elsewhere.
A sample means a test piece or a reference from the same ground. We can discuss a trial with your material before a larger spares order. A short run tells you more than a catalogue claim.
Ask how quickly a question is answered and who owns it. Our online service team replies within 8 hours. We focus on parts and settings that affect wear, so you get an actionable answer.
We have worked in dredging since 1994 and describe over 30 years in the field. Our range covers cutter suction dredgers, heads, teeth, pumps and the wear parts that tie them together. We publish a CSD series table so you can screen options first, and we accept custom builds when the standard envelope does not fit. Facilities are described as ISO 9001-certified, with robotic welding and in-house R&D; documentation is available on request. Export counts differ between pages, so we confirm the exact figure in writing. Our service team replies within 8 hours.
No. We do not list a product or brand under that name. Buyers use the phrase for dredging in hard, abrasive ground. For that duty we supply cutter suction dredgers, heads and replacement teeth. Describe your material and we will match the tooling.
Head choice depends on ladder class, depth and pipe bore, not rock type alone. We publish heads from 8 inch to the 36–38 inch band. Send your depth range and pipe bore and we will narrow it to a workable pair.
There is no fixed interval. Quartz content, grain shape and swing hours all change the rate. We ask for a sample and your target hours between changes, then propose a profile and stock level. Exact life is to be confirmed in writing.
It handles compacted soil, clay and rock within its power and depth envelope. Very hard unweathered rock may need pre-loosening. We review a sample first and tell you where the process stops being economical.
Send the material description, target depth, placement distance, hours per day and any required output. Add the pipe bore if it is fixed. With those points we can quote a dredger and a spares basket for your site.