You are here: Home » News » Jet Suction Dredger » Model Specifications » Jet Suction Dredger JSD250 Specifications and Output Guide for Contractors

Product Category

Jet Suction Dredger JSD250 Specifications and Output Guide for Contractors

Views: 0     Author: Site Editor     Publish Time: 2026-11-19      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
sharethis sharing button

Jet Suction Dredger JSD250 Specifications and Output Guide for Contractors

You have a spec sheet for a jet suction dredger and a site that does not match the brochure. The JSD250 numbers look generous until you ask what they assume about depth, discharge distance, and bed material. We walk buyers through the JSD table row by row, because a figure quoted without its test condition leads to a disappointed handover.

We start with the row that matters most to the job and work outward. A jet suction dredger JSD250 from ITECH Co.,Ltd. is a high-pressure jet system that loosens sand before a suction pump carries slurry to a discharge line. Here we read each published figure, show where depth fights discharge distance, and flag the gravel and power limits we confirm in writing.


What Is a Jet Suction Dredger JSD250?

Product Structure

The JSD250 is a floating dredger built around a high-pressure water jet and a sand suction pump. A jet ring at the suction head loosens the bed; the pump draws the slurry through a discharge pipe. The hull carries the main engine, pump, and anchor gear. You position the unit on cables and let the jet cut. Our jet suction dredger range uses this layout across the series.

How It Works

The jet pumps water into the sediment, lifting grains into suspension. The suction pump then moves the slurry to the discharge point. Because water does the loosening, the system suits sand under a clay cap and works in great depths, though hard clay still needs time to break down.


Why Use a Jet Suction Dredger JSD250?

Reaching Sand Beneath Clay Overburden

Many sand deposits sit under clay. A cutter dredger must chew through that cap first. A jet system works at the interface: water loosens the sediment and the pump extracts the sand beneath it, recovering target material with less disturbance.

High-Flow Transfer Through One Pipeline

The JSD250 pairs a 10/8 inch pump delivering 620 to 1450 m3/hr with a discharge line that carries slurry to a remote bank. There is no barge shuttle or reload step, and a head of 21 to 35 m gives room to plan the pipe run.

A Simple Principle With Fewer Wear Points

Water jet plus suction pump is a short mechanical chain. You avoid the cutter gearbox and teeth a cutter dredger consumes in abrasive ground. Wear concentrates in the pump and nozzles, which are easy to inspect, so maintenance stays predictable.

Configurable to the Work Site

We treat the published table as a starting point, not a fixed promise. The site note is explicit: data can be adjusted, and actual discharge and capacity depend on the work site. That helps when your pipe run sits near a table limit.


Jet Suction Dredger JSD250 Specifications

We read the JSD250 data sheet with you one line at a time. Each figure below is published; anything we cannot publish stays to be confirmed in writing.

Capacity and Production Rate

Published capacity is 130 to 260 m3/hr. The range spans loose sand and denser material, and output changes with the duty cycle. Work back from what you need per shift; do not read the top number as a guaranteed rate.

Pump Size, Flow and Head

The pump is listed as 10/8 inch, with flow from 620 to 1450 m3/hr and head from 21 to 35 m. Flow moves the slurry; head pushes it along the pipe and up to the bank. You need both to place material at distance. High flow with too little head stalls in a long line.

Dredging Depth and Discharge Distance

Maximum dredging depth is 15 m; maximum discharge distance runs from 200 to 1000 m. These figures pull against each other. Send slurry farther and you lose energy for lifting it from depth. We ask for both numbers before we say a JSD250 fits your pit.

Gravel Passing Limit

The JSD250 passes gravel up to 60 to 70 mm. That is a passing limit, not a crushing rating, and rounded river gravel behaves differently from sharp quarry stone. If your bed carries cobbles above that range, we will say the configuration is wrong.

Main Engine Power

Main engine power is 180 to 250 kW. The lower end suits shorter runs and shallower cuts; the upper end supports longer discharge and denser slurry. We size the engine to the whole circuit, not the pump alone, since power beyond what the line needs buys no output.

Customization in Writing

Every JSD figure can be adjusted to customer requirements, and actual discharge and capacity depend on the site. We put the agreed engine rating, pump size, and expected output in writing. Review the JSD250 specification page before you fix a number.

JSD Series Specification Comparison
Model
Capacity m3/hr
Max discharge m
Max gravel mm
Max depth m
Engine power kW
JSD200
80-110
200-600
50-60
15
132-156
JSD250
130-260
200-1000
60-70
15
180-250
JSD300
300-360
200-1500
60-70
15
250-300
JSD350
360-390
200-1800
60-70
20
300-410
JSD400
440-520
200-2000
60-80
20
410-460

ITECH Jet Suction Dredger JSD250 Options

The Standard Configuration

The JSD250 sits in the middle of the range. A 10/8 inch pump, 180 to 250 kW engine, and 200 to 1000 m discharge make it a common pick for medium sand work. It reaches 15 m and takes 60 to 70 mm gravel. Choose it when both limits cover your job.

Moving Up the JSD Range

When the pipe run passes 1000 m, we look at larger models. The JSD300 reaches 200 to 1500 m with 250 to 300 kW; the JSD400 goes to 2000 m with 410 to 460 kW. Moving up buys distance and capacity at the cost of more fuel and deck space.

Custom-Built Jet Suction Packages

Any published figure can be adjusted to your requirements. We build to a spec rather than force a standard hull onto the job. Tell us the depth, pipe length, and gravel size, and we will confirm the build in writing. Custom work takes longer, so plan the order date.


Applications of the Jet Suction Dredger JSD250

Sand Extraction Under Clay Layers

This is the JSD's strongest case. The jet loosens sediment at the clay interface and the pump extracts sand beneath it, so you avoid stripping the overburden first and recovery improves with less mixing.

Deep River and Lake Bed Recovery

The JSD works in great depths, which suits river and lake beds where sand sits below a water column. A floating unit positions over the deposit and pumps to shore, but the 15 m limit sets the boundary, so check the bed profile first.

Port and Channel Maintenance

Channels silt up and ports lose depth. A jet suction unit removes fine sand without a cutter head, limiting disturbance near structures, and discharge to a placement area keeps work continuous. Confirm the discharge distance first.

Borrow Pits and Reclamation Fill

Contractors use sand dredgers to feed reclamation and borrow pit operations. The JSD250's continuous flow suits a steady fill requirement; match pump output to the receiving site's capacity and confirm the solids content in writing.


Jet Suction Dredger JSD250 vs. Alternative

Jet Suction vs. Other Dredging Methods
Decision Factor
Jet Suction Dredger
Cutter Suction Dredger
Mechanical Grab
Loosening method
High-pressure water jet
Rotating cutterhead
Bucket digs directly
Best material
Sand beneath clay
Compacted soil and rock
Mixed debris and scrap
Conveyance
Slurry through pipeline
Slurry through pipeline
Barge haul cycle
Depth strength
Works in great depths
Varies by model
Limited by rope reach
Output pattern
Continuous flow
Continuous flow
Cyclical

How to Choose the Right Jet Suction Dredger JSD250?

Read Capacity Against the Site Cycle

Turn the 130 to 260 m3/hr figure into a shift target, then subtract downtime for anchors and pipe moves. A site with many relocations never reaches the peak, so we quote a realistic average rather than a headline rate.

Balance Depth and Discharge Distance

Depth and discharge distance compete for the same energy. If you need the full 1000 m run, expect to give up some of the 15 m depth. Write down both limits and we will tell you where the JSD250 stops fitting.

Check the Gravel Passing Limit

Measure the largest fraction in your bed, not the average. The 60 to 70 mm limit assumes material the pump can swallow. Angular stone or a few oversized cobbles change the answer. When in doubt, send a sample and we will review it.

Size the Main Engine Honestly

Match the 180 to 250 kW engine to the full pipeline, including bends and elevation. A longer line needs more head and power. Undersizing causes stalls; oversizing wastes fuel. We calculate against your actual route, not a short test line.

Confirm What Can Be Adjusted

Ask which figures are fixed and which are open. The site note allows adjustment, but not every limit moves. We mark the agreed engine, pump, and output figures in writing, so quote and handover match.


Installation Considerations

Supporting Structure

The hull carries the jet frame, pump, and engine, so it must float level and hold position against current. Anchor handling matters more than hull size in a flowing river: a unit that drags its anchors cuts an uneven trench.

Fixing Method

Fix the discharge pipe and position the jet head on a controlled winch, raising and lowering it without swinging into the hull. Check anchor lines before every shift; most JSD downtime comes from positioning, not the pump.

Project Requirements

Confirm the placement area, pipe route, and depth profile before delivery. Published capacity and discharge depend on the site, so we ask for those three inputs early, turning a spec sheet into a workable plan.


How to Choose a Jet Suction Dredger JSD250?

Specifications

List depth, discharge distance, gravel size, and required hourly output on one page. Compare the JSD250 against those four. If two sit at the table limit, ask us to check the combination rather than assume it will work together.

Customization

Tell us what you want to change: engine rating, pump size, or discharge layout. We build to the agreed spec and mark the rest to be confirmed in writing. Confirm the build sheet before the deposit, since late changes cost time.

Samples

Send a bed sample if gravel content is uncertain. A sample supports an honest statement on output and wear, so we test it rather than revise a quote after delivery.

Technical Support

Ask who commissions the unit and who supplies wear parts. We support start-up and confirm which parts we carry. Clear support terms matter once the dredger is on site and the first pipe run is being planned by your crew.


Why Choose ITECH?

We have built dredgers since 1994 and publish the JSD figures so buyers can check them before ordering. Our team walks the spec table with you line by line rather than sending one output number. You can read about our facilities on our company background page. Bring your depth, pipe run, and gravel size and we will tell you whether the JSD250 fits.


Frequently Asked Questions

Q1. What does the JSD250 actually produce?

Published capacity is 130 to 260 m3/hr, but that range depends on material and site. We would rather agree a realistic hourly figure in writing than quote the top and miss it at handover. Send your depth and pipe run.

Q2. How do depth and discharge distance trade off?

The JSD250 lists 15 m maximum depth and 200 to 1000 m maximum discharge. They compete because the same pump energy lifts slurry and pushes it down the line. Using the full discharge distance reduces the depth you can hold. Tell us both targets and we will check the combination.

Q3. What gravel can the JSD250 pass?

The stated limit is 60 to 70 mm. That is a passing size, not a guarantee for every shape of stone. Rounded gravel passes more easily than angular rock. If your bed carries larger cobbles, this hull is the wrong choice. Send a sample and we will confirm what is realistic.

Q4. How is engine power sized?

Main engine power is published as 180 to 250 kW. We size it against the whole circuit: pump, pipe length, bends, and elevation. A longer run needs more head and power. We confirm the final rating in writing so you do not pay for power the line cannot use.

Q5. Can the JSD250 be customized?

Yes. The site note says any data can be adjusted to customer requirements, and we accept customized dredgers. Engine rating, pump size, and discharge layout can be set to the job. Tell us your depth, distance, and gravel size and we will confirm the build before production.

Call Us :  (same as WhatsApp)
+8615027760800 (Leo)
+8615031104888 (Steven)
+8615954483680 (Richard Liu)
+963952189929 (Abdul)
Add:
Jinju Road, Qingzhou, Weifang, Shandong,  China.
B22, Rongsheng Business Zone, Shijiazhuang, China
Sulymanyeh, Al - Ourouba street , Aleppo, Syria

Quick Links

We will be committed to the development of global agents,
while in the mass production, adhere to customers from all over the world,Provide the best competitiveness price,high quality and professional technology support.

Product Category

 Copyrights 2026 ITECH Co.,Ltd. All rights reserved.