Views: 0 Author: Site Editor Publish Time: 2026-11-20 Origin: Site
A French dredging contractor rarely buys a pump on paper power. You buy it for the depth you must reach, the material you must lift and the hours the crew can keep it running. A drague suceuse hydraulique is specified around a hydraulic power pack, not just a pump curve, and that changes the whole conversation with a supplier.
We are ITECH Co.,Ltd., and we size hydraulic power packs for suction work before we discuss impellers. Below we cover hydraulic versus electric drive, the HSPD 80 to 300 range, the real limits of deep suction, and the maintenance routine that keeps hydraulic parts alive. The aim is a specification a project engineer can take into a tender meeting.
A hydraulic suction dredger is a pump, a hydraulic power pack and a control loop. The pump end holds the casing, impeller and wear parts; the pack holds the prime mover, oil pump, tank and valves. Hoses join the two. In a submersible build the electric motor is replaced by a hydraulic motor beside the impeller, so no long drive shaft runs through the water.
The pack sends pressurised oil to the hydraulic motor, which turns the impeller and draws slurry through the suction line. The volute converts speed into pressure and the mixture leaves through the discharge. A drague suceuse hydraulique is chosen as much for its pack as for its wet end. See our hydraulic dredge pump builds.
We start with the duty, not the engine. Flow, head, solids load and line length set the oil flow and pressure the pack must deliver. A pack sized to the real job holds speed when the material thickens; an undersized one slows the impeller and lets solids drop out of the line.
Hydraulic motors deliver high torque at low speed without a gearbox. That matters when the cutter meets compacted clay or the intake hits a gravel pocket. The motor slows rather than stalls, and the operator keeps control of the feed.
Dredged material rarely holds one density for a whole shift. With hydraulic drive the operator can trim oil flow to hold impeller speed as the slurry thickens. You keep pipeline velocity above the settling point without over-pumping the clean stretches.
A hydraulic submersible unit has no cable reel or underwater electrical joint. On a barge or a tracked carrier that removes a set of failure points. Recovery is a hose lift, and the wear parts come up with the pump.
Published facts and fields we confirm in writing are separated here. Do not treat an unconfirmed figure as a tender value.
Oil flow and pressure set impeller speed. We ask for discharge diameter, line length and solids concentration before we size the pack. Exact kW, oil flow and pressure for each model are to be confirmed in writing, because they follow the duty.
Wet parts for sand and gravel use high-chrome alloy; stainless steel is used where corrosion dominates. Hydraulic hose and seals are a separate wear budget. Ask for a part list that names the impeller, liner, casing and throat bush.
Depth is not a single number. Static lift, friction in the suction line and vapour margin all reduce what the pump can draw. Jet assistance can reach deeper layers by loosening the bed, but a drague suceuse hydraulique still obeys line losses. Maximum depth per model is to be confirmed in writing.
The HSPD family is listed in 80, 100, 150, 200, 250 and 300 classes. The HSPD-300 hydraulic pump dredger is one published configuration. Flow, head and power for each class are to be confirmed in writing.
Hose lengths, connector types and control valves vary with the carrier. We agree them in a drawing pack before build. Anything not on a published page stays marked to be confirmed in writing.
HSPD hydraulic dredger classes and what stays open | |||
Class | Published in our range | Confirm in writing | Typical working role |
|---|---|---|---|
HSPD 80 | 80 class | Flow, head, power, depth | Small channels and pond work |
HSPD 100 | 100 class | Flow, head, power, depth | Narrow canals and maintenance |
HSPD 150 | 150 class | Flow, head, power, depth | River bank and borrow pit |
HSPD 200 | 200 class | Flow, head, power, depth | Port silt removal |
HSPD 250 | 250 class | Flow, head, power, depth | Mid-volume sand transfer |
HSPD 300 | 300 class | Flow, head, power, depth | Capital dredging and long discharge |
These units run the hydraulic motor beside the impeller under water. A hydraulic wear-resistant submersible slurry pump suits abrasive sand where an electric joint would be a risk. The pack stays on the deck or bank.
The HSPD units are complete dredger packages: pump, power pack, hoses and controls on one frame. They suit crews that move between sites without rebuilding the drive each time.
Where the target lies under clay or at depth, a high-pressure water jet loosens the bed first and the pump carries the slurry out. This is a different process from plain suction and we quote it separately.
Canals and deep rivers accumulate soft silt that must be removed without draining the channel. Hydraulic drive lets the operator hold pump speed as the density changes through the shift.
Capital dredging cuts new basins and deepens berths. Volumes are large and the discharge run long, so pack capacity and line friction matter more than peak pump flow.
Jet-assisted systems loosen sand under a clay cap and lift it through the suction line. The jet breaks the layer and the pump moves the slurry. Each half must be sized to the other.
Mining slurry is coarse and often chemically active. High-chrome wet parts handle the abrasion, and the hydraulic layout keeps the drive clear of water entering the sump.
Hydraulic suction dredger versus a direct electric suction pump | ||
Dimension | Hydraulic suction dredger | Direct electric suction pump |
|---|---|---|
Drive | Oil pack and hydraulic motor at the pump | Electric motor on a cable or shaft |
Low-speed torque | High torque without a gearbox | Torque tied to motor design and drive |
Underwater joint | No electrical joint at the pump | Cable and motor joint submerged |
Depth change | Operator trims oil flow to hold speed | Speed set by supply and motor sizing |
Service focus | Oil, filters, hoses and seals | Cable, windings and bearings |
Best fit | Barges, remote sites, variable material | Fixed site with stable power |
Write down discharge distance, static lift and the solids you expect. Those three set oil flow and pressure. A pack chosen from a catalogue row alone will either bog down in heavy slurry or waste fuel on light work.
Separate geometric depth from hydraulic reach. Friction in a long suction hose can cost more head than the vertical lift itself. If the target is deep, ask whether jet assistance belongs in the scope.
Sharp sand cuts chrome parts faster than rounded gravel. Ask for the metallurgy of each wet part and set an inspection interval from the sample, not from a calendar.
Every bend, coupling and long hose run consumes pressure before it reaches the motor. Keep hoses short and straight where you can, and include the loss in the pack specification.
Hydraulic oil, filters and seals have a service rhythm of their own. Agree who changes them and where the spare kit lives before the unit ships. A pack without clean filters is a short-lived pack.
The pack needs a level, ventilated base on the barge or bank. The submerged pump hangs from a frame or guide that must take its weight and the drag of the hoses.
Secure hoses against chafe and strain at every bend. Quick couplings save time but must be rated for the working pressure; a blown line on a remote site ends the shift.
Confirm available prime-mover power, working depth and the discharge route. If the site has no crane, the package must be light enough for the crew's lifting gear.
Ask for flow, head, oil flow, pressure and wear material in one written sheet. Mark every unpublished value to be confirmed in writing, then compare offers line by line.
Tell us the carrier, hose length and control interface. A drague suceuse hydraulique built for a pontoon will not drop onto a tracked frame without adapter work.
A bucket of the bed material tells us more than a verbal description. It sets the impeller passage and the wear material. Send a sieve result if shipping is not possible.
Our online service team replies within eight hours. Confirm the spare kit and the filter schedule before you order, and name who on site is trained to change them.
We have built dredging equipment since 1994 and worked in the field for more than thirty years. Our ISO 9001 certified facilities use robotic welding, and our in-house group studies pump hydraulics and wear materials. We have shipped to many countries; the exact count is to be confirmed in writing.
On hydraulic packages we publish the HSPD size classes and hold the rest for a written data sheet. We ask for your line layout and material sample before we size the pack. That keeps the quotation tied to a real duty and avoids a surprise when the unit meets compacted ground.
It describes a suction dredger whose pump is driven by a hydraulic power pack rather than a direct electric drive. In a spec it should name the pump, the pack, the hoses and the control loop. Ask for oil flow and pressure alongside flow and head, since one without the other cannot be compared.
Depth depends on static lift, suction line friction and the vapour margin at the impeller, so there is no single figure. Jet assistance can reach deeper layers by loosening the bed first. We state the maximum depth for a given build in writing after we see your line layout.
It depends on the site. Hydraulic gives high torque at low speed and avoids underwater electrical joints, which helps on barges and remote work. Electric drive is simpler where stable power is available and the unit stays in one place. We compare both against your duty.
The family is listed in 80, 100, 150, 200, 250 and 300 classes. Pick from discharge distance, solids load and working depth rather than from the number alone. Flow, head and power for each class are to be confirmed in writing before you commit.
Oil condition, filter changes, hose inspection and seal replacement are the routine items. Keep a spare hose and seal kit on site, and log pressure at the motor so a slow loss of performance is visible early. Agree the service interval before delivery.