You are here: Home » News » Cutter Suction Dredger » 18 Inch Suction Discharge » DRAGA MARINA 18 Pulgadas Succion Descarga para Dragado

Product Category

DRAGA MARINA 18 Pulgadas Succion Descarga para Dragado

Views: 0     Author: Site Editor     Publish Time: 2026-11-20      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
sharethis sharing button

DRAGA MARINA 18 Pulgadas Succion Descarga para Dragado

Latin American buyers searching for a DRAGA MARINA 18" SUCCION/DESCARGA are usually solving a matching problem, not shopping for a hull. An 18-inch suction line only performs when the pump, cutter, pipe bore and discharge distance agree. Get that combination wrong and you either starve the pump or move slurry too slowly to keep solids in suspension. ITECH Co.,Ltd. configures 18-inch suction and discharge packages around the material and the placement route you have.

We work with project buyers in Spanish and English, and we keep the conversation practical. Tell us the sediment, the water depth and how far the pipeline must run, and we will set out the pump-and-pipe match in writing. This page covers that matching, the suction versus discharge layout, pipeline distance planning and what a custom build can change.


What Is DRAGA MARINA 18" SUCCION/DESCARGA?

Product Structure

The phrase describes a cutter suction dredger built around an 18-inch suction and discharge path. The 18-inch cutter suction dredger carries a ladder, rotating cutter head, suction mouth, slurry pump and a discharge line on floats. Winches position the machine and swing the head across the cut. The hull is dismountable and road-transportable in our published range, which matters for inland sites.

How It Works

The cutter loosens sediment at the bed. Water at the suction mouth turns it into slurry, and the pump pushes that slurry to the placement area. Suction sets what enters the pipe; discharge sets how far it travels. Both ends must be sized together. A strong pump behind an undersized mouth only pulls a vacuum, while a large cutter feeding a narrow pipe causes blockages and avoidable wear.


Why Use DRAGA MARINA 18" SUCCION/DESCARGA?

A Balanced 18-Inch Pump and Pipe

Flow and bore have to agree. Too much flow in a small pipe erodes the wall; too little in a large pipe lets sand settle. We check the pump curve against pipe diameter and the solids you expect, then state the match in writing. This check prevents most start-up problems.

Clear Suction and Discharge Layout

A well-laid suction side keeps air out and feeds the pump evenly. A well-laid discharge side keeps velocity high enough to carry solids. We draw both routes around your site, including bends and any lift. Short, straight runs on supported floats cost less than long detours.

Pipeline Distance Planning

Distance is not just a number on a drawing. Every metre adds friction, and every metre of lift adds head. We plan the route before fixing the pump, so the machine can place material where you need it. If one pump cannot cover the distance, we say so rather than promise output we cannot support.

Custom Build for Latin American Sites

Many projects arrive with a fixed pipeline corridor or a limited access road. We accept custom builds and adjust the package to those constraints. We work in Spanish and English, and we write specifications your local team can check on site.


DRAGA MARINA 18" SUCCION/DESCARGA Specifications

Pump and Pipe Bore

The 18-inch designation refers to the suction and discharge path. Exact flow, head and bore are to be confirmed in writing. For context, our published CSD series lists the CSD-400 at 2,200 m³/hr with 400/400 mm pipes and 700–1,200 kW, and the CSD-500 at 3,500 m³/hr with 600/500 mm pipes and 1,100–1,600 kW. The 18-inch class sits between those envelopes.

Dredging Depth Envelope

Depth is set by ladder length and series class. Published figures run from 1–5 m on the CSD-200 to 1.5–20 m on the CSD-700. We confirm working depth for your 18-inch build in writing, because depth and achievable output move together in real sediment.

Cutter Head and Teeth

Heads are published from 8 inch to the 36–38 inch band, with replacement teeth available. On an 18-inch package we choose a head that feeds the pump steadily, not one that breaks the most material. Bands, tooth patterns and wear-part quantities are to be confirmed in writing.

Discharge Distance and Head

Distance depends on friction, solids density and elevation change. Our hose range runs DN200 to DN1300, with pipe in HDPE, PE, UHMWPE and steel. We confirm achievable distance for your route in writing. Site conditions govern the final number.

Hull, Power and Transport

Standard dredgers are described as dismountable, road-transportable, fuel efficient and low maintenance. Installed power in the series runs from 160–300 kW to 2,800–3,500 kW by class. Power for your 18-inch build is to be confirmed in writing after we review material and pipeline.

Written Confirmation

Any figure not on our published pages stays unconfirmed until we put it in writing. That includes exact 18-inch flow, depth, fuel use, wear-part life and delivery schedule. We would rather mark a number as pending than let you budget on a guess.


ITECH DRAGA MARINA 18" SUCCION/DESCARGA Options

Standard 18-Inch Cutter Suction Dredger

This is the starting point for most enquiries. It brings ladder, cutter, pump and discharge line together as one machine, with the portability our standard range is known for. We check that depth and pipe match suit your site before recommending it.

Marine Suction and Discharge System

Some buyers own a hull or workboat and need the marine dredger with suction and discharge system as a package. We scope the pump, piping, floats and controls around what you have. Interface points are agreed in writing so installation does not stall.

Custom-Built Channel Package

Where the corridor, depth or material is unusual, we build to the brief. That can mean a revised discharge layout, a different wear package or a changed transport configuration. Tell us which parameter is fixed and we will show what has to give.


Applications of DRAGA MARINA 18" SUCCION/DESCARGA

River and Canal Desilting

Rivers and canals need steady removal without closing the waterway for long. An 18-inch package fits medium channels where a smaller unit lacks reach and a larger one lacks access. We plan the cut around flow and navigation windows.

Port and Harbour Maintenance

Work around berths demands predictable output and tight positioning. The suction and discharge layout must keep the pump fed while the head works close to structures. We review berth geometry before fixing the pipeline route.

Land Reclamation and Fill

Where dredged material becomes fill, placement distance and slurry density matter as much as production. We match the discharge line to the fill area and check that the solids arriving meet your specification. Fragment size is controlled at the cutter.

Pond and Lagoon Cleanup

Shallow, confined water bodies reward a portable, dismountable package. Setup time and the ability to move between ponds often decide the machine more than raw capacity. We plan the access route with the pumping layout.


DRAGA MARINA 18" SUCCION/DESCARGA vs. Plain Suction Dredging

The comparison below sets two generic processes against each other. It does not describe any other supplier or brand.

Cutter-assisted suction vs plain suction on an 18-inch line
Decision factor Cutter suction and discharge Plain suction dredging
Material Compacted soil, clay and rock Loose sand and soft silt
Loosening Rotating head breaks material first Relies on natural looseness
Solids size Controlled by head and teeth Limited to what the mouth can draw
Output stability Steady feed to the pump Varies with bed condition
Pipeline duty Head chosen to protect the pump Simpler, shorter runs
Best use Capital and maintenance work where material is firm Light clean-out of unconsolidated sediment

How to Choose the Right DRAGA MARINA 18" SUCCION/DESCARGA?

Start With the Placement Route

Map the discharge line before choosing the machine. Length, bends and lift decide the pump duty. A route that looks short on a plan can be expensive once floats and bends are added. We price the route as part of the package.

Decide What the Pump Must Carry

Describe the sediment by grain size and density. Coarse sand needs more velocity than fine silt to stay in suspension. We use that description to set the bore and confirm what the pump can move. Guessing here causes settled solids and blockages.

Check Depth Against Output

Deeper cuts reduce reachable output on most dredgers. Compare the depth you need with the series envelope, then ask us to confirm the 18-inch figure in writing. A machine that reaches the depth slowly may cost more than a larger class.

Account for Wear and Spares

Suction and discharge systems consume hoses, pipe, teeth and pump wet ends. We build the spares list around your planned hours, not a flat percentage. Stocking the right items avoids idle days on remote sites.

Confirm Transport and Assembly

Dismountable units travel by road. Check load limits on your access route and the space available for assembly. We state transport dimensions for a build in writing once the configuration is fixed.

18-inch package configuration matrix
Site condition Layout choice Consequence
Short flat pipeline Standard pump and bore Lowest operating cost
Long pipeline Higher head pump, larger bore More power, higher fuel use
Significant lift Staged pump plan Avoids solids drop-out
Coarse abrasive sand Wear-resistant pipe and wet ends Longer service intervals
Soft clay Head tuned for steady feed Protects pump from surges
Limited road access Dismountable modular build More assembly time on site

Installation Considerations

Supporting Structure

Floats must carry the discharge line and support bends. A line that sags traps solids and raises friction. We specify float spacing and support points as part of the layout, and confirm the arrangement for your route in writing.

Fixing Method

Pump, pipe sections and the suction assembly are joined so they can be inspected and replaced. We use couplings suited to abrasive slurry and state the joint method for each build. Access for change-out matters as much as holding pressure.

Project Requirements

Confirm water depth, placement distance, available power and the hours you can stop for maintenance. A remote site may need a larger spares stock and a clearer assembly plan. We factor these into the configuration from the start.


How to Choose a DRAGA MARINA 18" SUCCION/DESCARGA?

Specifications

Compare depth, output, bore and power on the same basis. Our series table gives published figures by class, while exact 18-inch numbers are to be confirmed in writing. Ask for suction and discharge diameter separately.

Customization

Tell us which part of the package is fixed: the corridor, the depth or the transport limit. We then adjust the rest. Custom builds are accepted, and we state the trade-off in output or cost before you commit.

Samples

For sediment, a sample is worth more than a description. A bag of the material and a note on grain size let us check the pump and pipe match. We can discuss a short trial before a full order.

Technical Support

You need a named contact who understands suction and discharge layouts. Our online service team replies within 8 hours. We answer with settings and part references, not generic literature, so your crew can act on the reply.


Why Choose ITECH?

We have worked in dredging since 1994 and describe more than 30 years in the field. Our published CSD series lets you screen classes before a conversation, and we accept custom builds when the standard envelope does not fit. We publish cutter heads, teeth, hoses from DN200 to DN1300 and pipe in HDPE, PE, UHMWPE and steel, so spares come from one source. Facilities are described as ISO 9001-certified, with robotic welding and in-house R&D; documentation is available on request. Export counts differ between pages, so we confirm the exact figure in writing. Our service team replies within 8 hours.


Frequently Asked Questions

Q1. What does "succion/descarga" mean on an 18-inch dredger?

It describes the suction side that draws slurry and the discharge side that carries it to the placement area. Both share the 18-inch path. We size them together, because a strong pump cannot fix a poor suction layout or an undersized pipe.

Q2. Can you confirm exact 18-inch flow and depth figures?

Not from the published pages. Exact figures for the 18-inch configuration are to be confirmed in writing. We can show the adjacent CSD-400 and CSD-500 rows for context, then issue a written specification after reviewing your material and route.

Q3. How far can the discharge pipeline run?

It depends on friction, solids density and lift. We plan distance against pump duty instead of quoting a single number. Send the route length and elevation change, and we will confirm what the package can sustain in writing.

Q4. Do you supply a complete package or only the dredger?

We scope the pump, piping, floats, cutter, teeth and supporting components around your site. Standard units are dismountable for road transport. Tell us what you already own and we will define the remaining scope.

Q5. Can we discuss the project in Spanish?

Yes. We work with Latin American project buyers in Spanish and English, and we write specifications your local team can verify. Send your questions to our contact page and we will reply within 8 hours.

Call Us :  (same as WhatsApp)
+8615027760800 (Leo)
+8615031104888 (Steven)
+8615954483680 (Richard Liu)
+963952189929 (Abdul)
Add:
Jinju Road, Qingzhou, Weifang, Shandong,  China.
B22, Rongsheng Business Zone, Shijiazhuang, China
Sulymanyeh, Al - Ourouba street , Aleppo, Syria

Quick Links

We will be committed to the development of global agents,
while in the mass production, adhere to customers from all over the world,Provide the best competitiveness price,high quality and professional technology support.

Product Category

 Copyrights 2026 ITECH Co.,Ltd. All rights reserved.