Views: 0 Author: Site Editor Publish Time: 2026-11-20 Origin: Site
Latin American buyers searching for a DRAGA MARINA 18" SUCCION/DESCARGA are usually solving a matching problem, not shopping for a hull. An 18-inch suction line only performs when the pump, cutter, pipe bore and discharge distance agree. Get that combination wrong and you either starve the pump or move slurry too slowly to keep solids in suspension. ITECH Co.,Ltd. configures 18-inch suction and discharge packages around the material and the placement route you have.
We work with project buyers in Spanish and English, and we keep the conversation practical. Tell us the sediment, the water depth and how far the pipeline must run, and we will set out the pump-and-pipe match in writing. This page covers that matching, the suction versus discharge layout, pipeline distance planning and what a custom build can change.
The phrase describes a cutter suction dredger built around an 18-inch suction and discharge path. The 18-inch cutter suction dredger carries a ladder, rotating cutter head, suction mouth, slurry pump and a discharge line on floats. Winches position the machine and swing the head across the cut. The hull is dismountable and road-transportable in our published range, which matters for inland sites.
The cutter loosens sediment at the bed. Water at the suction mouth turns it into slurry, and the pump pushes that slurry to the placement area. Suction sets what enters the pipe; discharge sets how far it travels. Both ends must be sized together. A strong pump behind an undersized mouth only pulls a vacuum, while a large cutter feeding a narrow pipe causes blockages and avoidable wear.
Flow and bore have to agree. Too much flow in a small pipe erodes the wall; too little in a large pipe lets sand settle. We check the pump curve against pipe diameter and the solids you expect, then state the match in writing. This check prevents most start-up problems.
A well-laid suction side keeps air out and feeds the pump evenly. A well-laid discharge side keeps velocity high enough to carry solids. We draw both routes around your site, including bends and any lift. Short, straight runs on supported floats cost less than long detours.
Distance is not just a number on a drawing. Every metre adds friction, and every metre of lift adds head. We plan the route before fixing the pump, so the machine can place material where you need it. If one pump cannot cover the distance, we say so rather than promise output we cannot support.
Many projects arrive with a fixed pipeline corridor or a limited access road. We accept custom builds and adjust the package to those constraints. We work in Spanish and English, and we write specifications your local team can check on site.
The 18-inch designation refers to the suction and discharge path. Exact flow, head and bore are to be confirmed in writing. For context, our published CSD series lists the CSD-400 at 2,200 m³/hr with 400/400 mm pipes and 700–1,200 kW, and the CSD-500 at 3,500 m³/hr with 600/500 mm pipes and 1,100–1,600 kW. The 18-inch class sits between those envelopes.
Depth is set by ladder length and series class. Published figures run from 1–5 m on the CSD-200 to 1.5–20 m on the CSD-700. We confirm working depth for your 18-inch build in writing, because depth and achievable output move together in real sediment.
Heads are published from 8 inch to the 36–38 inch band, with replacement teeth available. On an 18-inch package we choose a head that feeds the pump steadily, not one that breaks the most material. Bands, tooth patterns and wear-part quantities are to be confirmed in writing.
Distance depends on friction, solids density and elevation change. Our hose range runs DN200 to DN1300, with pipe in HDPE, PE, UHMWPE and steel. We confirm achievable distance for your route in writing. Site conditions govern the final number.
Standard dredgers are described as dismountable, road-transportable, fuel efficient and low maintenance. Installed power in the series runs from 160–300 kW to 2,800–3,500 kW by class. Power for your 18-inch build is to be confirmed in writing after we review material and pipeline.
Any figure not on our published pages stays unconfirmed until we put it in writing. That includes exact 18-inch flow, depth, fuel use, wear-part life and delivery schedule. We would rather mark a number as pending than let you budget on a guess.
This is the starting point for most enquiries. It brings ladder, cutter, pump and discharge line together as one machine, with the portability our standard range is known for. We check that depth and pipe match suit your site before recommending it.
Some buyers own a hull or workboat and need the marine dredger with suction and discharge system as a package. We scope the pump, piping, floats and controls around what you have. Interface points are agreed in writing so installation does not stall.
Where the corridor, depth or material is unusual, we build to the brief. That can mean a revised discharge layout, a different wear package or a changed transport configuration. Tell us which parameter is fixed and we will show what has to give.
Rivers and canals need steady removal without closing the waterway for long. An 18-inch package fits medium channels where a smaller unit lacks reach and a larger one lacks access. We plan the cut around flow and navigation windows.
Work around berths demands predictable output and tight positioning. The suction and discharge layout must keep the pump fed while the head works close to structures. We review berth geometry before fixing the pipeline route.
Where dredged material becomes fill, placement distance and slurry density matter as much as production. We match the discharge line to the fill area and check that the solids arriving meet your specification. Fragment size is controlled at the cutter.
Shallow, confined water bodies reward a portable, dismountable package. Setup time and the ability to move between ponds often decide the machine more than raw capacity. We plan the access route with the pumping layout.
The comparison below sets two generic processes against each other. It does not describe any other supplier or brand.
Cutter-assisted suction vs plain suction on an 18-inch line | ||
Decision factor | Cutter suction and discharge | Plain suction dredging |
|---|---|---|
Material | Compacted soil, clay and rock | Loose sand and soft silt |
Loosening | Rotating head breaks material first | Relies on natural looseness |
Solids size | Controlled by head and teeth | Limited to what the mouth can draw |
Output stability | Steady feed to the pump | Varies with bed condition |
Pipeline duty | Head chosen to protect the pump | Simpler, shorter runs |
Best use | Capital and maintenance work where material is firm | Light clean-out of unconsolidated sediment |
Map the discharge line before choosing the machine. Length, bends and lift decide the pump duty. A route that looks short on a plan can be expensive once floats and bends are added. We price the route as part of the package.
Describe the sediment by grain size and density. Coarse sand needs more velocity than fine silt to stay in suspension. We use that description to set the bore and confirm what the pump can move. Guessing here causes settled solids and blockages.
Deeper cuts reduce reachable output on most dredgers. Compare the depth you need with the series envelope, then ask us to confirm the 18-inch figure in writing. A machine that reaches the depth slowly may cost more than a larger class.
Suction and discharge systems consume hoses, pipe, teeth and pump wet ends. We build the spares list around your planned hours, not a flat percentage. Stocking the right items avoids idle days on remote sites.
Dismountable units travel by road. Check load limits on your access route and the space available for assembly. We state transport dimensions for a build in writing once the configuration is fixed.
18-inch package configuration matrix | ||
Site condition | Layout choice | Consequence |
|---|---|---|
Short flat pipeline | Standard pump and bore | Lowest operating cost |
Long pipeline | Higher head pump, larger bore | More power, higher fuel use |
Significant lift | Staged pump plan | Avoids solids drop-out |
Coarse abrasive sand | Wear-resistant pipe and wet ends | Longer service intervals |
Soft clay | Head tuned for steady feed | Protects pump from surges |
Limited road access | Dismountable modular build | More assembly time on site |
Floats must carry the discharge line and support bends. A line that sags traps solids and raises friction. We specify float spacing and support points as part of the layout, and confirm the arrangement for your route in writing.
Pump, pipe sections and the suction assembly are joined so they can be inspected and replaced. We use couplings suited to abrasive slurry and state the joint method for each build. Access for change-out matters as much as holding pressure.
Confirm water depth, placement distance, available power and the hours you can stop for maintenance. A remote site may need a larger spares stock and a clearer assembly plan. We factor these into the configuration from the start.
Compare depth, output, bore and power on the same basis. Our series table gives published figures by class, while exact 18-inch numbers are to be confirmed in writing. Ask for suction and discharge diameter separately.
Tell us which part of the package is fixed: the corridor, the depth or the transport limit. We then adjust the rest. Custom builds are accepted, and we state the trade-off in output or cost before you commit.
For sediment, a sample is worth more than a description. A bag of the material and a note on grain size let us check the pump and pipe match. We can discuss a short trial before a full order.
You need a named contact who understands suction and discharge layouts. Our online service team replies within 8 hours. We answer with settings and part references, not generic literature, so your crew can act on the reply.
We have worked in dredging since 1994 and describe more than 30 years in the field. Our published CSD series lets you screen classes before a conversation, and we accept custom builds when the standard envelope does not fit. We publish cutter heads, teeth, hoses from DN200 to DN1300 and pipe in HDPE, PE, UHMWPE and steel, so spares come from one source. Facilities are described as ISO 9001-certified, with robotic welding and in-house R&D; documentation is available on request. Export counts differ between pages, so we confirm the exact figure in writing. Our service team replies within 8 hours.
It describes the suction side that draws slurry and the discharge side that carries it to the placement area. Both share the 18-inch path. We size them together, because a strong pump cannot fix a poor suction layout or an undersized pipe.
Not from the published pages. Exact figures for the 18-inch configuration are to be confirmed in writing. We can show the adjacent CSD-400 and CSD-500 rows for context, then issue a written specification after reviewing your material and route.
It depends on friction, solids density and lift. We plan distance against pump duty instead of quoting a single number. Send the route length and elevation change, and we will confirm what the package can sustain in writing.
We scope the pump, piping, floats, cutter, teeth and supporting components around your site. Standard units are dismountable for road transport. Tell us what you already own and we will define the remaining scope.
Yes. We work with Latin American project buyers in Spanish and English, and we write specifications your local team can verify. Send your questions to our contact page and we will reply within 8 hours.
How Much Does A Cutter Suction Dredger Cost? — China Price Guide (2025)
The Global Landscape of Cutter Suction Dredger Equipment Manufacturers
Cutter Suction Dredger for Sand Dredging Leading Machine Manufacturers
Portable Cutter Suction Dredger: China Factory Transport Planning Guide
How Long Is The Lead Time for A New Cutter Suction Dredger From China?